Search found 4313 matches

by Tech_Marco
Fri Nov 03, 2017 12:31 pm
Forum: DSP X7
Topic: Rotary Engraving?
Replies: 20
Views: 2317

Re: Rotary Engraving?

I don't know what is wrong here?! I always allow my customer to send the card back for upgrade, didn't even read my posts before? And instead of charging $30, I only asked my customers to pay for the shipping and basic $10 for handling fee? Did I ask too much? If you still think that $10 still cost ...
by Tech_Marco
Fri Nov 03, 2017 12:03 pm
Forum: DSP X7
Topic: Rotary Engraving?
Replies: 20
Views: 2317

Re: Rotary Engraving?

The new feature launched on Oct 2016! I don't promise n one that the U axis for rotary would be installed or whatever, I only told that the feature was on my wising list to get the programmer to add it. You have a whole year to get send it to me for upgrade but you didn't and now getting pissed on m...
by Tech_Marco
Fri Nov 03, 2017 11:46 am
Forum: DSP X7
Topic: Rotary Engraving?
Replies: 20
Views: 2317

Re: Rotary Engraving?

When did you purchase it? What is your order number? Raycam doesn't cost any $ and you're free to download it
I have mentioned that for certain customers (within certain time), they can send the card back to me to upgrade.
by Tech_Marco
Fri Nov 03, 2017 11:32 am
Forum: CO2 Laser Discussion
Topic: x7 dsp controller and synrad j48-2
Replies: 1
Views: 148

Re: x7 dsp controller and synrad j48-2

I never setup a RF system so I don't have hands on experience with that. There were a few post associated with RF and X7 that have been discussed before. You may want to search those posted from the forum. FYI, to the best my understand that what you need to do is to set the X7 for RF by selecting '...
by Tech_Marco
Fri Nov 03, 2017 11:24 am
Forum: DSP X7
Topic: Rotary Engraving?
Replies: 20
Views: 2317

Re: Rotary Engraving?

You can't use U axis for rotary on X7 without running Raycam. You have to setup 'Y' axis or 'X' for that purpose.

Marco
by Tech_Marco
Wed Nov 01, 2017 10:32 am
Forum: DSP E5
Topic: How do I turn on "Pre-ignition" for RF?
Replies: 1
Views: 121

Re: How do I turn on "Pre-ignition" for RF?

See image
Preignition.jpg


You can't change the % or time because it should be handled by your RF tube/ circuitry internally
For RF, I was told that the frequency should be set to '5000Hz'

Marco
by Tech_Marco
Tue Oct 31, 2017 5:15 pm
Forum: CO2 Laser Discussion
Topic: Beam Expander Recommendation
Replies: 3
Views: 196

Re: Beam Expander Recommendation

I'll go for 2.0x if possible. You may get better collimation result. However, there is a 'drawback'. Now the beam angle will be sharper so you will have more 'slope' on the cutting edge. But engraving should be improved much better because of wider beam and more fine beam spot. If you want to offset...
by Tech_Marco
Sat Oct 28, 2017 4:18 pm
Forum: CO2 Laser Discussion
Topic: Beam Expander Recommendation
Replies: 3
Views: 196

Re: Beam Expander Recommendation

Hey Chris: A little busy here so didn't answer your PM message in time. Sorry about it smile (We're making some products for a winery and it kept me busy like an ant. Plus, we just got a new ocean shipment, there are some new 'toy' for me to play like the Hybrid metal/non-metal machine) You may go f...
by Tech_Marco
Wed Oct 25, 2017 2:26 pm
Forum: CO2 Laser Discussion
Topic: 130W Hybrid
Replies: 1
Views: 165

Re: 130W Hybrid

We haven't much info to share yet until we finished some test. The 130W may not get nice cut on 2mm stainless steel because it has to run at very slow like 3~4mm/s. I was told that it could cut well on 1.5mm with decent speed and result. For sure the 150W will handle the 2mm stainless and 4mm mild s...
by Tech_Marco
Fri Oct 20, 2017 8:58 am
Forum: New Product on the board
Topic: Lightobject CO2 Hybrid cutter machine for metal & non-metal
Replies: 0
Views: 404

Lightobject CO2 Hybrid cutter machine for metal & non-metal

A new shipment just arrived and with this shipment, there is a new member to join LightObject: Hybrid CO2 Laser Metal/Non-metal cutter! Hybrid01.jpg Hybrid02.jpg Hybrid03.jpg Hybrid04.jpg With a 130W laser tube installed, it can cut through 2mm stainless steel and 4mm mild steel with Oxygen assisted...
by Tech_Marco
Wed Oct 11, 2017 10:46 pm
Forum: D40/K40 small chinese CO2 laser machine
Topic: Max output
Replies: 2
Views: 232

Re: Max output

You won't get 40W from this tube (assuming 720-750mm long) but possible 35W at most. In general this tube output 32W. The tube was manufactured a year ago so you may experience lower power output, possible at 25W now. Current for the tube should never go over 15mA but most K40 doesn't has a current ...
by Tech_Marco
Mon Oct 09, 2017 10:01 pm
Forum: DSP R5
Topic: Is the LO RDworks V8.01.16 available?
Replies: 28
Views: 3041

Re: Is the LO RDworks V8.01.16 available?

I have posted the update here
viewtopic.php?f=55&t=2793

Marco
by Tech_Marco
Wed Sep 27, 2017 9:38 am
Forum: DSP X7
Topic: Raycam only in Chinese
Replies: 1
Views: 171

Re: Raycam only in Chinese

The issue found. The language file 'lang_eng.ini' was missing. It may be caused by unzipped program or it could be removed by anti-virus program but we have no idea. The Zip file we posted included the language file, though. What you need to do is to download the language file and save it to the fol...
by Tech_Marco
Tue Sep 26, 2017 7:23 am
Forum: DSP T9
Topic: Lightobject new DSP laser controller card
Replies: 60
Views: 4260

Re: Lightobject new DSP laser controller card

Will carry some 5V I/O board soon
Relay output
by Tech_Marco
Wed Sep 20, 2017 8:03 pm
Forum: DSP T9
Topic: Samples from T9 DSP controller
Replies: 32
Views: 1680

Re: Samples from T9 DSP controller

I won't be surprised it was wiring issue or other hardware issue.

For the new issue ( actually not an issue) just read the FAQ and you will get it. Plus , two others folks just posted similar questions about that so I am not going to repeat again here.

Go to advanced search