Search found 41 matches

by overkill71
Tue Feb 02, 2016 2:49 pm
Forum: DSP X7
Topic: Outputs not working correctly - Bad 708C card?
Replies: 4
Views: 609

Outputs not working correctly - Bad 708C card?

Marco, Spoke with you earlier today about my KERN laser conversion problem. This is on my work laser, a Kern 150 watt RF laser, that we converted after I had such great success with my home DK 40 laser conversion. Everything is working great on the conversion except two items. We are trying to wire ...
by overkill71
Sun Jan 10, 2016 2:01 pm
Forum: DSP X7
Topic: Need Help! Wiring an RF Laser Tube to AWC608 LO-X7
Replies: 3
Views: 602

Re: Need Help! Wiring an RF Laser Tube to AWC608 LO-X7

Laserdude,

THANK YOU! worked like a charm.


Russell
by overkill71
Sat Jan 09, 2016 6:30 pm
Forum: DSP X7
Topic: Need Help! Wiring an RF Laser Tube to AWC608 LO-X7
Replies: 3
Views: 602

Re: Need Help! Wiring an RF Laser Tube to AWC608 LO-X7

Laserdude, Thanks for the fast reply! I will give it a go when I get in the shop tomorrow morning. I'll post the results.


Thanks again!
by overkill71
Sat Jan 09, 2016 5:13 pm
Forum: DSP X7
Topic: Need Help! Wiring an RF Laser Tube to AWC608 LO-X7
Replies: 3
Views: 602

Need Help! Wiring an RF Laser Tube to AWC608 LO-X7

Hello all and thanks in advanced. Here is the project that I am working on and the trouble that I am having. I have a very old (approx. 15years old) 150 Watt KERN Laser system with an RF Laser Tube with an approximate table size of 48" x 24'. The old kern software is horrible to mess with so I ...
by overkill71
Sat Jun 06, 2015 4:39 pm
Forum: D40/K40 small chinese CO2 laser machine
Topic: Z-Table: threaded posts are not straight
Replies: 8
Views: 1563

Re: Z-Table: threaded posts are not straight

Got my z table working. I had to put a .030" washer on top of each of the 4 post on the top rails of the fixture. The problem is that the 4 threaded rods were all different lengths. Once I installed the washer shims, the table now has full travel up and down. I even installed a Z axis lower lim...
by overkill71
Fri Jun 05, 2015 7:20 pm
Forum: D40/K40 small chinese CO2 laser machine
Topic: Z-Table: threaded posts are not straight
Replies: 8
Views: 1563

Re: Z-Table: threaded posts are not straight

Not meaning to hi-jack your post but figured here is a good place to post mine. Marco, I have the same problem. I got my table today, assembled it and all wired up very easy. Table just grunts. Took apart and have two bent threaded rods and a third rod has the belt retaining ring off of it. Any chan...
by overkill71
Sun May 31, 2015 11:10 am
Forum: DSP X7
Topic: LaserCAD install can't find CorelDraw
Replies: 13
Views: 2126

Re: LaserCAD install can't find CorelDraw

zkmiller,

Not sure this is what your looking for but at the bottom of this post it has the 64bit USB driver.

viewtopic.php?f=55&t=2484



~Russell
by overkill71
Sun May 24, 2015 6:47 am
Forum: DSP X7
Topic: Will this power supply work for X7 upgrade? ---- SOLVED
Replies: 3
Views: 848

Re: Will this power supply work for X7 upgrade?

Got it!! Used info from this post: http://www.lightobject.info/viewtopic.php?f=70&t=2286&hilit=power+supply+wiring Have full laser power control as well. Now to set all parameters in the dsp and laser cad. Its sending file over and displays correct on dsp but engravers it in mirror image. An...
by overkill71
Sat May 23, 2015 8:50 pm
Forum: DSP X7
Topic: Will this power supply work for X7 upgrade? ---- SOLVED
Replies: 3
Views: 848

Re: Will this power supply work for X7 upgrade?

Ok, got machine wired up and running!!! Switched to English and was able to run duck sample program and I was able to transfer a drawing from lasercad and run it. These "runs" were all dry runs, no laser, just movement of x and y axis. Machine homes correctly as well. I could really use so...
by overkill71
Thu May 21, 2015 3:32 pm
Forum: DSP X7
Topic: Will this power supply work for X7 upgrade? ---- SOLVED
Replies: 3
Views: 848

Re: Will this power supply work for X7 upgrade?

A couple more shots...

Thanks!
by overkill71
Thu May 21, 2015 3:11 pm
Forum: DSP X7
Topic: Will this power supply work for X7 upgrade? ---- SOLVED
Replies: 3
Views: 848

Will this power supply work for X7 upgrade? ---- SOLVED

Hello to everyone and Thank You in advance for any help you can give me. I have a DK40 style machine I bought from HUHUShop off amazon and I have ordered the X7 upgrade kit. After some extensive reading I had a question (or two). It appears that the power supply that comes with the machine stays as ...

Go to advanced search