Search found 19 matches

by neuman5022
Tue Jan 16, 2018 7:14 pm
Forum: DSP X7
Topic: Door switch NO or NC
Replies: 1
Views: 95

Door switch NO or NC

Hi guys,

The door switch on the X7 (port 11 IN) - is it NO or NC ? Have seen some conflicting diagrams.

To make it clear - when door is closed - should the controller get closed circuit or open circuit to allow the machine to work ?

Cheers

Isaac
by neuman5022
Tue Jan 16, 2018 6:45 pm
Forum: DSP X7
Topic: Water, Door, foot safety features
Replies: 3
Views: 121

Re: Water, Door, foot safety features

Hi again Kees, In the LO DSP connection diagram - the water sensor is connected only to the laser PSU. In TROCEN diagram - the water protection (cooler) is connected to both - the controller AND the laser PSU. If I wish to connect my water sensor to the controller as mentioned above - do I need to c...
by neuman5022
Sat Jan 06, 2018 11:04 pm
Forum: DSP X7
Topic: Water, Door, foot safety features
Replies: 3
Views: 121

Water, Door, foot safety features

Hi Guys,


Those safety features - are they stopping only the laser from firing or the laser AND machine movement ?

Cheers

Isaac
by neuman5022
Sat Jan 06, 2018 3:44 am
Forum: DSP X7
Topic: First time firing my LO-x7 - got some issues
Replies: 4
Views: 191

Re: First time firing my LO-x7 - got some issues

Hi SWMS Yes - I have set my machine to the X and Y range, and when the machine homes, I can't move beyond the 0,0 and also beyond my range setting (in my case 550 and 300) My concern was that the machine rejects the option of hard limits. I have 2 CNC machines where I Installed hard limit switches b...
by neuman5022
Thu Jan 04, 2018 9:32 pm
Forum: DSP X7
Topic: First time firing my LO-x7 - got some issues
Replies: 4
Views: 191

Re: First time firing my LO-x7 - got some issues

Thanks Kees

I am using RayCam, however I assume your advice will be the same for LaserCad too.

I did not know about the SHIFT + STOP option - I will give it a go.

Thanks

Isaac
by neuman5022
Sat Dec 30, 2017 7:30 pm
Forum: DSP X7
Topic: First time firing my LO-x7 - got some issues
Replies: 4
Views: 191

First time firing my LO-x7 - got some issues

Hello guys, Fired up the X7 - X,Y Z axis are working fine. Two issues: (I ran this without the Laser PSU) 1. I cannot set the Hardware limit switches in the manufacturer parameter page - I press the "read" then tick the HW limit and "save" with password, press "Reset" a...
by neuman5022
Fri Dec 29, 2017 3:21 pm
Forum: CO2 Laser Discussion
Topic: Laser Off/On switch questions
Replies: 2
Views: 170

Re: Laser Off/On switch questions

Thanks Marco

Yes - I think to have a switch that will cut-off both functions at the LPSU is the best option.

Isaac
by neuman5022
Thu Dec 28, 2017 11:23 pm
Forum: CO2 Laser Discussion
Topic: Laser Off/On switch questions
Replies: 2
Views: 170

Laser Off/On switch questions

Hi Guys, I would like to have an additional switch to the emergency and main power, which I can control the tube mainly for running dry runs without the laser firing. My question is - where do I put the laser off/on switch ? One option will be to have a separate mains line to the laser PSU - and put...
by neuman5022
Mon Dec 25, 2017 2:02 am
Forum: Electronics
Topic: water flow/pressure sensor connection LSR-H2OPRSN
Replies: 2
Views: 172

Re: water flow/pressure sensor connection LSR-H2OPRSN

Thanks for the answer.

IMHO - this information should be sent with the product itself, ths way you can avoid these kind of questions...

Cheers

Isaac.
by neuman5022
Mon Dec 18, 2017 7:59 pm
Forum: Electronics
Topic: water flow/pressure sensor connection LSR-H2OPRSN
Replies: 2
Views: 172

water flow/pressure sensor connection LSR-H2OPRSN

Hi Guys, Can'r figure out this little gizmo... Unit came with a T connector, and a 7mm small tube.... What is he small tube for ? Does the 90 degrees way of the connector go to the inlet ? There is a small screw with Phillips head - is this for adjusting the triggering flow ? On the back there is a ...
by neuman5022
Sun Dec 17, 2017 6:26 pm
Forum: Tips and new on the DSP & Software
Topic: LO X7 and RDworks
Replies: 1
Views: 148

LO X7 and RDworks

Hello guys,


Can the LO X7 work OK with RDworks v8 ?

I have found some very good youtube videos on how to work with RDworks - so I wonder if the X7 is OK with this SW.

Many thanks


Isaac
by neuman5022
Thu Dec 07, 2017 2:38 pm
Forum: Temperature Controller
Topic: Water temp safety
Replies: 4
Views: 235

Water temp safety

Hello guys

I read that water temp is very important for tube's life.

Is there a way to have a water temp meter to stop the laser from firing when it gets under or over a specific temp (Sort of like the flow switch)

If yes - how do I connect it ?

Many thanks

Isaac
by neuman5022
Tue Dec 05, 2017 4:36 pm
Forum: Digital/ Analog Meter
Topic: Analog meter questions
Replies: 1
Views: 241

Analog meter questions

Hi

Is an analog amp meter supplied when ordering a 850mm 40w tube ?

If not what kind of analog meter should I pick for this tube ?

I understand I do not need a shunt because it is built in - please verify this is true.

Many thanks
by neuman5022
Fri Dec 01, 2017 4:06 pm
Forum: DSP X7
Topic: Cannot find Raycam manual
Replies: 0
Views: 143

Cannot find Raycam manual

Hello all,

Downloaded the Raycam SW - however I did not find the manual under the manuals section of the forum.

Can someone direct me where to look for it ?

Many thanks


Isaac
by neuman5022
Mon Aug 31, 2015 4:25 pm
Forum: CO2 Laser Discussion
Topic: 40W Vs 45W ?
Replies: 8
Views: 1596

Re: 40W Vs 45W ?

Hi Marco, Thank yo for your kind offer. I think it is best to wait until I am ready to put the tube in. There is no logic to invest now in something I will use who knows when, while I need the money to get the parts for these stages. When time comes - I will be in touch. Once I will finish the frame...

Go to advanced search