Search found 4269 matches

by Tech_Marco
Wed Sep 20, 2017 8:03 pm
Forum: DSP T9
Topic: Samples from T9 DSP controller
Replies: 32
Views: 688

Re: Samples from T9 DSP controller

I won't be surprised it was wiring issue or other hardware issue.

For the new issue ( actually not an issue) just read the FAQ and you will get it. Plus , two others folks just posted similar questions about that so I am not going to repeat again here.
by Tech_Marco
Wed Sep 20, 2017 12:30 pm
Forum: DSP T9
Topic: Samples from T9 DSP controller
Replies: 32
Views: 688

Re: Samples from T9 DSP controller

Yes
For 2M415, the Opo is equivalent of +5V on other type of stepping motor driver
See the manual: viewtopic.php?f=93&t=3603

I may add another diagram for other type motor driver to avoid confusion. On X7 manual, it should show

Marco
by Tech_Marco
Tue Sep 19, 2017 11:07 pm
Forum: DSP T9
Topic: Samples from T9 DSP controller
Replies: 32
Views: 688

Re: Samples from T9 DSP controller

Simply way to solve your issue is to replace the limit switch to a regular mechanical switch or a magnetic type without feeding power required. If you have to use electrical type limit switch, find one with 5V power. I don't know why you couldn't get Y to move. If Y didn't move and didn't get the Y ...
by Tech_Marco
Tue Sep 19, 2017 10:58 pm
Forum: CO2 Laser Discussion
Topic: 80 watt PS with 100 watt laser tube
Replies: 3
Views: 46

Re: 80 watt PS with 100 watt laser tube

Sorry I oversight your message. I though you're trying to drive a 80W laser tube with a 100W laser power supply. The fact is that you're trying to do other way. In this case, same thing that you need to monitor the current not being over or the laser power supply could be 'overloaded' and get burned...
by Tech_Marco
Mon Sep 18, 2017 6:08 pm
Forum: CO2 Laser Discussion
Topic: 60W Power supply keeps failing
Replies: 9
Views: 89

Re: 60W Power supply keeps failing

To me it is not acceptable for a machine not able to run at 400mm/s for engraving! Our machine require to run at least 550mm/s as a minimum standard before we allow it to leave our shop. I used to do my engraving work for at least 550mm/s in most case. 600mm/s or 650mm.s is not uncommon here in our ...
by Tech_Marco
Mon Sep 18, 2017 8:52 am
Forum: CO2 Laser Discussion
Topic: 60W Power supply keeps failing
Replies: 9
Views: 89

Re: 60W Power supply keeps failing

60W is great for engraving. Even a 80W is still doing a very good job!
For 40W laser tube, it sometimes may not get you enough power for deep engraving when speed like 500mm/s or up
by Tech_Marco
Sun Sep 17, 2017 10:43 pm
Forum: CO2 Laser Discussion
Topic: 60W Power supply keeps failing
Replies: 9
Views: 89

Re: 60W Power supply keeps failing

I think you need to pay closed attention to your laser tube. 3 power supply broken in a year sounds unbelievable. When the laser power supply arcing, either the transformer of LPSU defective or the laser tube is leaking gas! Not sure why you unplugged the current meter. To us, it is one of the most ...
by Tech_Marco
Sun Sep 17, 2017 10:36 pm
Forum: CO2 Laser Discussion
Topic: 80 watt PS with 100 watt laser tube
Replies: 3
Views: 46

Re: 80 watt PS with 100 watt laser tube

Yes you can do it but you must limited the current to 26mA (max 28mA) for better to the tube. You may get boost cutting power but just pay more attention on the current. If the machine doesn't has any current monitor meter, you better get one and installed in series with the laser tube in the Ground...
by Tech_Marco
Sat Sep 16, 2017 4:57 pm
Forum: Tips and new on the DSP & Software
Topic: RAYCAM V12 and LO-x7 question
Replies: 30
Views: 939

Re: RAYCAM V12 and LO-x7 question

Great it worked so I haven't wasted my time :D :D
If you like our services, please post some feedback on CNCZone.com, SawMillCreek.org, and/or Google review+Facebook. Sorry for asking many 'like' smile

Have a great weekend. Now I can watch my favor team(CF): Go Cougs!!

Marco
by Tech_Marco
Sat Sep 16, 2017 4:13 pm
Forum: Tips and new on the DSP & Software
Topic: RAYCAM V12 and LO-x7 question
Replies: 30
Views: 939

Re: RAYCAM V12 and LO-x7 question

Then it is your position relative issue. Just click the button on the menu bar and find one "Positive Relative". Change it to whatever position of your limit switch, in this case, it is Top Left
by Tech_Marco
Sat Sep 16, 2017 4:09 pm
Forum: Tips and new on the DSP & Software
Topic: RAYCAM V12 and LO-x7 question
Replies: 30
Views: 939

Re: RAYCAM V12 and LO-x7 question

Also, your position relative is not right
See the Blue dot. It should be at the Top Left corner
by Tech_Marco
Sat Sep 16, 2017 4:07 pm
Forum: Tips and new on the DSP & Software
Topic: RAYCAM V12 and LO-x7 question
Replies: 30
Views: 939

Re: RAYCAM V12 and LO-x7 question

I need you to draw a square of 20mm x 20mm. I don't care where but you must try each area to get the square cut.
I think you may have 'um' issue
by Tech_Marco
Sat Sep 16, 2017 4:04 pm
Forum: Tips and new on the DSP & Software
Topic: RAYCAM V12 and LO-x7 question
Replies: 30
Views: 939

Re: RAYCAM V12 and LO-x7 question

Draw 'One' circle at a time and placed it on each corner one at a time. No more than two circle for this test. That way, it will get yourself an idea which corner worked and which one doesn't.
by Tech_Marco
Sat Sep 16, 2017 3:50 pm
Forum: Tips and new on the DSP & Software
Topic: RAYCAM V12 and LO-x7 question
Replies: 30
Views: 939

Re: RAYCAM V12 and LO-x7 question

Pay attention your Range!
Why you set 1200 for X and 900for Y??
Aren't you working on a k40 with 300x200 range?
by Tech_Marco
Sat Sep 16, 2017 3:27 pm
Forum: Tips and new on the DSP & Software
Topic: RAYCAM V12 and LO-x7 question
Replies: 30
Views: 939

Re: RAYCAM V12 and LO-x7 question

where is the raycam manual. I have the LOX7 manual. Where do I find the keypad zero? From this forum manual download area Pretty much that the operation for both LaserCad and Raycam are the same for your issue. You press "Origin" on your keypad to set 'Origin'. There is no such thing &quo...

Go to advanced search