Search found 4362 matches

by Tech_Marco
Mon Jul 16, 2018 8:32 pm
Forum: DSP 608
Topic: Need some quick help
Replies: 1
Views: 30

Re: Need some quick help

"608"

-M
by Tech_Marco
Fri Jul 13, 2018 9:33 pm
Forum: D40/K40 small chinese CO2 laser machine
Topic: LO-X7 XY Limit Switches Inop
Replies: 5
Views: 281

Re: LO-X7 XY Limit Switches Inop

Any update?

Marco
by Tech_Marco
Wed Jul 11, 2018 6:00 pm
Forum: DSP T9
Topic: T9 Raster Engraving Memory
Replies: 2
Views: 87

Re: T9 Raster Engraving Memory

You may try to clean up memory and give it another try
Also, can you send me the file for testing?

Thanks
Marco
(In China)
by Tech_Marco
Thu Jun 28, 2018 4:20 am
Forum: D40/K40 small chinese CO2 laser machine
Topic: LO-X7 XY Limit Switches Inop
Replies: 5
Views: 281

Re: LO-X7 XY Limit Switches Inop

It seems that you didn't plug those two connectors deep enough to the sockets. Unplugged it and plug it in again firmly. No reason it worked for a night but not after.

Marco
by Tech_Marco
Wed Jun 27, 2018 6:39 pm
Forum: DSP T9
Topic: Any tips in preparing Adobe Illustrator artwork?
Replies: 8
Views: 274

Re: Any tips in preparing Adobe Illustrator artwork?

Bob Currently I am taking a business trip ( and vacation) to Japan and Hong Kong. So, I can run the file for you. I will forward to your case to my assistant " Master Will" to handle your case. I will visit the manufacturer in mid July and your case will be in the agenda. We are trying to ...
by Tech_Marco
Mon Jun 25, 2018 9:01 pm
Forum: D40/K40 small chinese CO2 laser machine
Topic: LO-X7 XY Limit Switches Inop
Replies: 5
Views: 281

Re: LO-X7 XY Limit Switches Inop

Either NO or NC, you still need to use X- and Gnd
Since you are using N.C., you need to change logic level in the parameters setup. If current setup is for Positive, then change it to negative

Marco
by Tech_Marco
Sat Jun 23, 2018 9:44 pm
Forum: Tips and new on the DSP & Software
Topic: Raycam back to Lasercad Steps.
Replies: 4
Views: 361

Re: Raycam back to Lasercad Steps.

As opposite, we don't support LaserCad no more
The Raycam is supported but we don't provide an upgrade from LaserCad to Raycam. If you need to switch back to LaserCad, we can send you a patch. After downgraded, you can use LaserCad

Marco
(In Japan)
by Tech_Marco
Sat Jun 23, 2018 9:04 pm
Forum: Tips and new on the DSP & Software
Topic: Raycam back to Lasercad Steps.
Replies: 4
Views: 361

Re: Raycam back to Lasercad Steps.

Hi Sam It has been almost two years after Raycam launched for X7. We decided not to provide LaserCad switch over service no more. It is because there were so much work involved and not all people like the Raycam over the LaserCad after upgraded. One guy got upset because Y movement is disabled once ...
by Tech_Marco
Fri Jun 22, 2018 5:59 pm
Forum: D40/K40 small chinese CO2 laser machine
Topic: Z Table Dip Switch Settings
Replies: 3
Views: 233

Re: Z Table Dip Switch Settings

You may test the motor movement before putting it into the Z table. That way you can tell if connection is correct or not. Also, check the motor wire pair. Sometime the motor wire terminal mapping sequences is different . Example:
A+A-, B+B- or. A+ B+ ,A- B-

Marco
by Tech_Marco
Tue Jun 19, 2018 4:14 pm
Forum: CO2 Laser Discussion
Topic: Real time auto focus tracking system for CO2 laser
Replies: 15
Views: 1594

Re: Real time auto focus tracking system for CO2 laser

We are in the process setting it up for video. Hopefully we can run the basic demo in this week. Then, we will try to make an mounting bracket for real test afterward I am taking a vacation to Japan, Taiwan, Hong Kong :D Then, I will spend two weeks in China trying to finalize the design. We are thi...
by Tech_Marco
Tue Jun 19, 2018 3:59 pm
Forum: DSP T9
Topic: Any tips in preparing Adobe Illustrator artwork?
Replies: 8
Views: 274

Re: Any tips in preparing Adobe Illustrator artwork?

If ou chosen English and it still showing Chinese. I found that it was caused by the window security. What you need to do is to copy the English language from the installation folder and paste it into the folder that you installed will fix it. It happened not only to Lasersoft but to the LaserCad an...
by Tech_Marco
Tue Jun 19, 2018 10:53 am
Forum: DSP T9
Topic: Any tips in preparing Adobe Illustrator artwork?
Replies: 8
Views: 274

Re: Any tips in preparing Adobe Illustrator artwork?

When you save the file, it allows you to select version to save as , choose very 8.0 is the most stable for most laser controller. We are working with then programmer and hope to get one out to support more update Illustrator.

Marco
by Tech_Marco
Mon Jun 18, 2018 9:28 pm
Forum: DSP T9
Topic: Any tips in preparing Adobe Illustrator artwork?
Replies: 8
Views: 274

Re: Any tips in preparing Adobe Illustrator artwork?

Save it in Illustrator version V8.0 and give it a try

Marco
(in Japan)
by Tech_Marco
Fri Jun 15, 2018 12:12 pm
Forum: CO2 Laser Discussion
Topic: Real time auto focus tracking system for CO2 laser
Replies: 15
Views: 1594

Re: Real time auto focus tracking system for CO2 laser

Yes, it is completed and in final testing phase. It works really good if you're cutting speed is under 30mm/s. The reason I didn't launch it yet becauseI found that if the cutting speed is 50mm/s of faster, the speed of the powered telescope couldn't catch up. But the true is that, In reality you ha...

Go to advanced search