Search found 4379 matches

by Tech_Marco
Sun Nov 18, 2018 9:06 pm
Forum: DSP T9
Topic: Corel Support?
Replies: 5
Views: 141

Re: Corel Support?

Yes, it is in the " to do list"
G code and DXF is also under development.
Once I have update from the design team, I will post it here

Marco
by Tech_Marco
Sun Nov 18, 2018 2:00 pm
Forum: DSP X7
Topic: New X7 screen issue
Replies: 4
Views: 38

Re: New X7 screen issue

You can correct the directionn issue through the software setup. Review the manual and the FAQ in this site.

Marco
by Tech_Marco
Fri Nov 16, 2018 12:52 pm
Forum: DSP E5
Topic: Manuf. Parameters, "Apply" box is not active
Replies: 2
Views: 30

Re: Manuf. Parameters, "Apply" box is not active

What you need to do is "Read, change, then Save". It will ask you for the password. Put down "608" and Reset the controller, the new setting should be taken in effect.

Marco
by Tech_Marco
Thu Nov 15, 2018 9:25 pm
Forum: DSP X7
Topic: New X7 screen issue
Replies: 4
Views: 38

Re: New X7 screen issue

You better check polarity of poweto the controller board. We usually tested the controller prior to ship. Also, double check two black cables are connected firmly to the LCD and the interface box. Fire from pressing the test button on the laser power supply had nothing to do with the controller. Marco
by Tech_Marco
Wed Nov 14, 2018 5:48 pm
Forum: DSP E5
Topic: How to reset on E5 pad to origin
Replies: 6
Views: 42

Re: How to reset on E5 pad to origin

First thing you must done is to make sure there is a " talk" between the PC and the DSP card. You need to install driver or it won't communicate. Parameters setup must gone through the LaserCad in your case.

-M
by Tech_Marco
Wed Nov 14, 2018 1:45 pm
Forum: DSP E5
Topic: How to reset on E5 pad to origin
Replies: 6
Views: 42

Re: How to reset on E5 pad to origin

That mean you haven't configured the gantry direction properly. Where I'd your limit swiches installed at? You can stop the gantry when power it up before hitting the ramp. Then, go to parameters setup uner Option. Look at something name ' Datum' and set the direction , for X and/or Y or both See FA...
by Tech_Marco
Wed Nov 14, 2018 11:27 am
Forum: Repair & Upgrade
Topic: Golden Laser at Elk Grove
Replies: 0
Views: 57

Golden Laser at Elk Grove

Machine: Goldern Laser 900x600 Issue: Alignment & burned focus lens Client: Tim ================================================================================================= Tim bought his machine from Southern California because he didn't know that we're around :cry: He said if he knew us h...
by Tech_Marco
Wed Nov 14, 2018 11:05 am
Forum: DSP E5
Topic: How to reset on E5 pad to origin
Replies: 6
Views: 42

Re: How to reset on E5 pad to origin

There is a button 'Origin' at the bottom Left. Press it and it will set the current laser head location as the Origin

Marco
by Tech_Marco
Mon Nov 12, 2018 11:23 am
Forum: DSP T9
Topic: SVG support. Beta ready!
Replies: 1
Views: 80

Re: SVG support. Beta ready!

New LightObject 'LaserSoft' V7.22.1
viewtopic.php?f=55&t=3773

Marco
by Tech_Marco
Sat Nov 10, 2018 7:36 pm
Forum: CO2 Laser Discussion
Topic: Plasma Dancing At Aperture ... arcing? Normal?
Replies: 2
Views: 109

Re: Plasma Dancing At Aperture ... arcing? Normal?

This is totally normal. No worry at all.
If it was spark like or yellow, then it is time to get worry

Marco ;)
by Tech_Marco
Sat Nov 10, 2018 7:14 pm
Forum: DSP T9
Topic: Backlash compensation?
Replies: 14
Views: 497

Re: Backlash compensation?

You can draw a box say 100x100mm with speed set to 550 to 600 or any speed you want to test. Set the mode to engraving. Scan Gap changed from 0.1 to 0.5 or 1 or 2. You check the starting and the ending see if lines are even or one long, one short

Hope this answered your question

Marco
by Tech_Marco
Sat Nov 10, 2018 9:39 am
Forum: DSP T9
Topic: SVG support. Beta ready!
Replies: 1
Views: 80

SVG support. Beta ready!

Good news, after pushing the design team so hard, finally the support of SVG is getting better improvement! It can open most SVG files and it take less time to open. I will post the beta 7.22.1 soon

Yeap!!

Marco ;)
by Tech_Marco
Thu Nov 08, 2018 7:06 pm
Forum: DSP T9
Topic: T9 / Laser PSU WP Switch Settings... FRUSTRATED
Replies: 4
Views: 118

Re: T9 / Laser PSU WP Switch Settings... FRUSTRATED

You have to hit the 'Download' button in order to get proper image uploaded, parameters of speed &power will be uploaded as well. For example, if you draw new items without pressing the Download button, it is not only laser won't fire but laser won't cut the image as well. The reason you got las...
by Tech_Marco
Wed Nov 07, 2018 9:34 pm
Forum: DSP T9
Topic: Communications Error
Replies: 8
Views: 625

Re: Communications Error

Make sire driver for the controller is installed properly. You should see the driver properly showed up under Window, the Device Manager. Some computer that I worked from my customers were either Firewall blocked, or have some sort of application blocking it. It took me long to get the driver to ins...
by Tech_Marco
Wed Nov 07, 2018 9:32 pm
Forum: DSP T9
Topic: T9 / Laser PSU WP Switch Settings... FRUSTRATED
Replies: 4
Views: 118

Re: T9 / Laser PSU WP Switch Settings... FRUSTRATED

If you are doing cutting, check the power of "Minimum" beside the "Maximum". Btw, you can bypass WP protection on the laser by placing a wire over the WP and Gnd terminals on the laser power supply. Make sure water is running or you will regret. I don't suggest people to bypass w...

Go to advanced search