Search found 10 matches

by asbest
Fri Apr 17, 2015 10:46 am
Forum: D40/K40 small chinese CO2 laser machine
Topic: Dimension XY guider wheel
Replies: 1
Views: 1459

Dimension XY guider wheel

Hi! I have a laser engraver (400 x 300 mm - model unknown , I did it a few times modernization ) . It's the age of seven. Most recently, it gives a very curved line cutting . Seat horizontally and vertically pulled . I suppose that stoch or deformed nylon wheels on the fixture head . That's why I'd ...
by asbest
Mon Jan 31, 2011 8:12 pm
Forum: DSP X7
Topic: DSP shows "System Reset"
Replies: 5
Views: 1693

Re: DSP shows "System Reset"

Hello!
Unfortunately, DSP has been damaged. I'd like to buy new commerical DSP CO2 Laser Engraving/ Cutter Controller ELSR-4XDSPV2 (Blue front panel) supporting CorelDraw & AutoCad.
What kind of software comes with it and what other softwares can using for DSP?
Thanks.
by asbest
Wed Jan 19, 2011 11:53 pm
Forum: DSP X7
Topic: DSP shows "System Reset"
Replies: 5
Views: 1693

Re: DSP shows "System Reset"

I have Silver/White front panel.
by asbest
Wed Jan 19, 2011 2:21 pm
Forum: DSP X7
Topic: DSP shows "System Reset"
Replies: 5
Views: 1693

DSP shows "System Reset"

Hello! I have a big trouble. My DSP works without protection against differences in an electrical network (shame on me). Recently the electricity suddenly was gone has disappeared and has instantly appeared. After that DSP shows an inscription "System Reset" and it works is nothing. I don'...
by asbest
Sat Jan 08, 2011 2:46 pm
Forum: DSP X7
Topic: DSP controller works astably
Replies: 1
Views: 837

DSP controller works astably

Hello!
When I am adjusting DSP using "RLaserCut V 2.0" program - everything is o'key. But the next time DSP doesn't remember last tasks(adjusts). I have to adjust DSP every time again.
I use CorelDraw 14, password gxfc88.
Thanks.
by asbest
Wed Dec 22, 2010 9:13 am
Forum: DSP X7
Topic: Can I make seals and stamps using software 'RLaserCut v2?
Replies: 1
Views: 912

Can I make seals and stamps using software 'RLaserCut v2?

Hello!
Can I make seals and stamps using software 'RLaserCut v2.0' on the rubber?
If yes what kind of modes needed?
by asbest
Wed Dec 15, 2010 12:02 pm
Forum: DSP X7
Topic: Speed of scan engraving doesn't grow
Replies: 4
Views: 1096

Re: Speed of scan engraving doesn't grow

Thanks, Tim!
I've coordinated controller and program speeds. And then adjusted acceleration sweep speeds X Y axis (up 10 to 8000 mm/sec). It was generally.
Unfortunately, program can't scan engraving objects separately - it will be very convenient and faster.
by asbest
Tue Dec 14, 2010 12:02 pm
Forum: DSP X7
Topic: Speed of scan engraving doesn't grow
Replies: 4
Views: 1096

Speed of scan engraving doesn't grow

Hello! I use DSP controller. When I'm trying to grow speed (from 10 mm/sec to 20 and more) it doesn't. Moreover. When I make speed 20 and more quality is completely lost (strong tortuous along the edges) when I make it more (>30), the laser head makes long continuous line, stops and on a board is wr...
by asbest
Thu Oct 28, 2010 10:13 am
Forum: DSP X7
Topic: Escape to the opposite side
Replies: 2
Views: 919

Escape to the opposite side

Hi! Recently I bought DSP controller board , two stepper drivers PSD5042-2P and upgraded my old chines laser machine (Moshi). I have now a problem. When I turn it on the head go to the limits (in my case upper right corner) and then in couple seconds laser head promptly escapes to the opposite side ...

Go to advanced search